Author Topic: Ooo happy day  (Read 4672 times)

0 Members and 1 Guest are viewing this topic.

Offline ukric

  • Platinum Member
  • ******
  • Posts: 4543
  • Chasing Da Clouds
Re: Ooo happy day
« Reply #15 on: July 27, 2013, 10:18:51 PM »
Spooning?

Offline Fiona

  • Global Moderator
  • Diamond Member
  • *****
  • Posts: 15052
  • I dont like cold tea!
Re: Ooo happy day
« Reply #16 on: July 27, 2013, 10:25:39 PM »
Cotton buds  ;D

Offline Rocc

  • Hero Member
  • *****
  • Posts: 758
  • The best tea is cold
Re: Ooo happy day
« Reply #17 on: July 28, 2013, 07:13:16 AM »
i cut the 510 connector on my 19b down till it is flush with the top cap. when i get a 7 mm x .5 bottoming tap and a arbor press i will push out the center pin and bushing from the 510 to make the hole deep so i can remover the design and chamfer from the top of the mod.

Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #18 on: July 28, 2013, 07:28:16 AM »
Sounds good. I tried sanding down my 510 connector on the 19b by hand. What a pigs ear I made of that. Still not managed to get the inside bit of the connector screwed out from underneath either (the bit with the spring on and the delrin) so have just given up on it for now. Guess having a lathe has benefits!

E-Cig-Reviews.com - Forum

Re: Ooo happy day
« Reply #18 on: July 28, 2013, 07:28:16 AM »



Offline Rocc

  • Hero Member
  • *****
  • Posts: 758
  • The best tea is cold
Re: Ooo happy day
« Reply #19 on: July 28, 2013, 07:42:34 AM »
use the tip of a sharp knife to remove the bur and a can of compressed air to remove the grit form the sandpaper form the hole and your back in business mate ;D

Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #20 on: July 28, 2013, 07:53:40 AM »
Cheers Rocc, I'll give it a bash at some point. It's packed away in a box right now as I'm moving over next few days

It was getting the delrin out from under the head cap that foxed me. I think Ric or Mev said they used a dremel to cut into it so they could use a screwdriver on it. Anyways, it'll have to wait now until I get another chance

Offline Rocc

  • Hero Member
  • *****
  • Posts: 758
  • The best tea is cold
Re: Ooo happy day
« Reply #21 on: July 28, 2013, 08:09:42 AM »
im in hopes of just pushing it out form the top side after i remove the center pin if i can that is. if i have to i will cut it out and just make a new one to replace it when i'am done with the top cap.

Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #22 on: July 28, 2013, 08:18:59 AM »
Good luck!

E-Cig-Reviews.com - Forum

Re: Ooo happy day
« Reply #22 on: July 28, 2013, 08:18:59 AM »



Offline zarf

  • Hero Member
  • *****
  • Posts: 598
  • Tin-foil milliner wonders what happened to avatar?
Re: Ooo happy day
« Reply #23 on: July 28, 2013, 01:42:23 PM »
the lathe has made it up onto the bench lol soon the mods will flow like the salmon flocking back to Capistrano :P
very,very nice lathe. good turn of phrase too - pmsl.

once you're in production, there may be a need for marketing those mods. and you have an excellent moniker to exloit: Rocc

maybe summat like "Roccam's Razor" - the mod that gets to the point.  or taglines like: "simplicity, gets improved" , "pursuing advanced simplicity" ,"simply. done." , etc.

Dunno. On the other hand  you might prefer to create "arcane" mods ...

Either way, that looks like a lovely piece of kit.


Offline Rocc

  • Hero Member
  • *****
  • Posts: 758
  • The best tea is cold
Re: Ooo happy day
« Reply #24 on: July 28, 2013, 09:51:54 PM »
thanks Zarf.

here the top part of the bottom button on my 19b i know it hard to see but i made it alittle easier to remove and i think it looks good too
« Last Edit: July 29, 2013, 12:14:36 AM by Rocc »

Offline Mev

  • Full Member
  • ***
  • Posts: 212
  • Spanking-D-Monkey
Re: Ooo happy day
« Reply #25 on: July 30, 2013, 05:58:15 PM »
 That's one nice looking lathe..... :D

Ilegal... it was the bottom pin I cut a slot in to remove it as it was stuck fast...  the top pin came out easily.

Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #26 on: July 30, 2013, 06:24:01 PM »
That's one nice looking lathe..... :D

Ilegal... it was the bottom pin I cut a slot in to remove it as it was stuck fast...  the top pin came out easily.

No worries, it might have been Ric then unless I got the wrong end of the stick

E-Cig-Reviews.com - Forum

Re: Ooo happy day
« Reply #26 on: July 30, 2013, 06:24:01 PM »



Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #27 on: July 30, 2013, 06:30:22 PM »
Yep, it was you Mev, I think you might have thought I was talking about the glued switch in the base of the mod? I was (and still am) having grief with the connector head brass/delrin etc:

http://e-cig-reviews.com/forum/index.php/topic,7118.msg142513.html#msg142513

Offline Mev

  • Full Member
  • ***
  • Posts: 212
  • Spanking-D-Monkey
Re: Ooo happy day
« Reply #28 on: July 30, 2013, 07:47:05 PM »
yeah i thought you meant the switch mate, which is what I cut a slot into..

Offline ilegal

  • Hero Member
  • *****
  • Posts: 1266
  • Five coils to Yuma
Re: Ooo happy day
« Reply #29 on: July 30, 2013, 07:51:54 PM »
No worries, I think someone glued my top cap for a laugh lol but there ya go  :'(